Fuente POWER PRODUCT™ 12VDC 1.4AmpPOWER PRODUCT™ 12VDC 1.4Amp Power SupplyFuente de Alimentación 12V, 1,4A. Montaje autoadhesivo. Terminales de entrada y Salida por cable (sin conector). Aislamiento tensión 3000VCA. Protección temporal de cortocircuito (<1 minuto) tensión de entrada 195-255VC.This product is intended for general use to feed electric and electronic devices in covered rooms, in environments without risk of explosion. Suitable to place inside cameras of security systems. Mounting with self-adhesive tape. Stabilized output voltage. Voltage 12 VDC - 1.4 Amp. Input - twin-lead power wire with double insulation. Output - twin-lead wire. Protection degree IP20.

Fuente ELMDENE™ 12 VDC 3Amp con RespaldoELMDENE™ 12 VDC 3Amp Boxed Power Supply with BatteryFuente de alimentación 12 V, 3 A. En caja. Incorpora LED que indica de alimentación, LED carga de batería, LEDs fallo salida o fusible fundido. Anti-sabotaje. Capacidad baterías 2x17 Amp.The EN range of power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing Intruder Alarm Systems to grade 3 under PD6662:2010 / EN50131, with built in quality and reliability. Comprehensive Battery Management. Deep Discharge Protection. Battery Fault Detection (grade 3). Double Battery Model has independent Battery Charging & Monitoring. Dedicated Fault Outputs. EPS Fault (mains fail). APS Fault (battery fault) (grade 3). PSU Fault (general fault). Internal LED PSU Status. Full Rated Current To Load + Battery Charging. Electronic Overload Protection. Mains Transient Protection. Output (mains on): 13.8V dc nominal. Load Output: 34 Maximum 3.0A 12 hours - 2.8/3.0A. Mains Supply: 230V +10%/-15%@50Hz. Environment: -10C to 40C @ 95%RH. Enclosure Type R: 410 H x 390 W x 90 D (Clam Lid). Box Sizes for battery: '34' models: 2 x 17 or 18Ah 3.0A**. Standards: EN3 - Grade 3 Environmental Class II. **Full current to load plus additional current to charge standby battery.

Fuente ELMDENE™ 12 VDC 3AmpELMDENE™ 12 VDC 3Amp Boxed Power SupplyFuente de alimentación 12vdc 3 A en caja. Incorpora LED que indica de alimentación, LED carga de batería, LEDs fallo salida o fusible fundido. Anti-sabotaje. Máximo tamaño de batería 7 A. Medidas 350 x 330 x 80 mm.The ‘N’ range of power supplies has been specifically designed for General Purpose applications including Access Control and CCTV that require a cost effective solution without the need for special features that can be found on our other ranges of Power Supplies. Full Rated Current to Load + Battery Charging. LED Indication. Mains Status. Output Fuse Failure. Battery Fuse Failure*. Standby Battery Operation*. Electronic Overload Protection. Mains Transient Protection. Front Tamper Protection. *Dependant on model. Output (mains on): 13.8V dc nominal. Load Output: 1 Amp. Max Battery Capacity 1 A: 1x7Ah. Mains Supply: 230V ac +10%/-15%@50Hz. Environment: -10C to 40C @ 95%RH. Dimensions: 200 H x 230 W x 80 D (Hinge Lid). Range: 1.0A*. *Full current to load plus additional 0.5A for charging the standby battery.

Fuente ELMDENE™ 12 VDC 2AmpELMDENE™ 12 VDC 2Amp Boxed Power SupplyFuente de alimentación 12vdc 2 A en caja. Incorpora LED que indica de alimentación, LED carga de batería, LEDs fallo salida o fusible fundido. Anti-sabotaje. Máximo tamaño de batería 7 A. Medidas 350 x 330 x 80 mm.The ‘N’ range of power supplies has been specifically designed for General Purpose applications including Access Control and CCTV that require a cost effective solution without the need for special features that can be found on our other ranges of Power Supplies. Full Rated Current to Load + Battery Charging. LED Indication. Mains Status. Output Fuse Failure. Battery Fuse Failure*. Standby Battery Operation*. Electronic Overload Protection. Mains Transient Protection. Front Tamper Protection. *Dependant on model. Output (mains on): 13.8V dc nominal. Load Output: 1 Amp. Max Battery Capacity 1 A: 1x7Ah. Mains Supply: 230V ac +10%/-15%@50Hz. Environment: -10C to 40C @ 95%RH. Dimensions: 200 H x 230 W x 80 D (Hinge Lid). Range: 1.0A*. *Full current to load plus additional 0.5A for charging the standby battery.

Fuente ELMDENE™ 12 VDC 1.5AmpELMDENE™ 12 VDC 1.5Amp Boxed Power SupplyFuente de alimentación 12vdc 1,5 A en caja. Incorpora LED que indica de alimentación, LED carga de batería, LEDs fallo salida o fusible fundido. Anti-sabotaje. Máximo tamaño de batería 7 A. Medidas 320 x 200 x 80 mmThe ‘N’ range of power supplies has been specifically designed for General Purpose applications including Access Control and CCTV that require a cost effective solution without the need for special features that can be found on our other ranges of Power Supplies. Full Rated Current to Load + Battery Charging. LED Indication. Mains Status. Output Fuse Failure. Battery Fuse Failure*. Standby Battery Operation*. Electronic Overload Protection. Mains Transient Protection. Front Tamper Protection. *Dependant on model. Output (mains on): 13.8V dc nominal. Load Output: 1 Amp. Max Battery Capacity 1 A: 1x7Ah. Mains Supply: 230V ac +10%/-15%@50Hz. Environment: -10C to 40C @ 95%RH. Dimensions: 200 H x 230 W x 80 D (Hinge Lid). Range: 1.0A*. *Full current to load plus additional 0.5A for charging the standby battery.

Transformador Genérico de IntrusiónAlarm Panels Universal TransformerTransformador 220/18 Vca - 45 VA220/18 Vca - 45 VA Transformer.

Flash COOPER™ 1490BZGCOOPER™ 1490BZG Flash Indicador con LED amarillo y zumbador. Compacto y de bajo consumo para la señalización remota de alarma, anormalidad o sí por medio de LED de alta visibilidad. Adecuados para la adaptación a los detectores de humo y / o térmicos instalados en falsos techos o suelos técnicos, para lo cual se requiere una señalización externa.Extremely compact optical indicator with a very high quality/price ratio that allows remote signalling of alarms, anomalies or others through highly luminous and low consumption LED. BZ versions incorporate a buzzer for intermittent or continuous optical-acoustical signalling (selectable by internal jumper). Power supply available at both 12V and 24V, selectable through internal jumper. The YELLOW LED ensures good visibility in all directions by emitting fixed or intermittent light. Simple and quick mounting thanks to the terminal connections and the possibility of fixing it with two-sided tape (included).

Flash COOPER™ 1490BZVCOOPER™ 1490BZV Flash Indicador con LED verde y zumbador. Compacto y de bajo consumo para la señalización remota de alarma, anormalidad o sí por medio de LED de alta visibilidad. Adecuados para la adaptación a los detectores de humo y / o térmicos instalados en falsos techos o suelos técnicos, para lo cual se requiere una señalización externa.Extremely compact optical indicator with a very high quality/price ratio that allows remote signalling of alarms, anomalies or others through highly luminous and low consumption LED. BZ versions incorporate a buzzer for intermittent or continuous optical-acoustical signalling (selectable by internal jumper). Power supply available at both 12V and 24V, selectable through internal jumper. The GREEN LED ensures good visibility in all directions by emitting fixed or intermittent light. Simple and quick mounting thanks to the terminal connections and the possibility of fixing it with two-sided tape (included).

Flash Estroboscópico COOPER™COOPER™ Stroboscopic FlashFlash estroboscópico ámbar IP54 de alta eficiencia. Amplia gama de fuente de alimentación: de 9 a 60 Vdc. La base de bayoneta está diseñado para simplificar el montaje.IP54 stroboscopic lamp. The increased functionality of the Solex permits a much reduced range of products and therefore allows a simplified stock holding and easier choice for the installer. The wide operating voltage, increased efficiency and automatic synchronization of the Solex make them a universal solution for all types of alarm and monitoring system. The bayonet base has been designed to allow a common mounting for most of Cooper signalling alarm products. The shallow base is suited to concealed wiring allowing installation with minimum visual impact.

Falsa Sirena CQR™CQR™ Dummy SounderDUMMY Carcasa sirena MULTIBOX base azulDummy Multibox - Blue. The Multibox comes with a choice of 6 individually shaped covers to meet a selection of applications. Dimensions: W:140mm H:175mm D:58mm. Covers available: Virgo - Leo - Corona - Taurus - Aries - Libra.

Falsa Sirena HONEYWELL™HONEYWELL™ Dummy SounderDUMMY Carcasa sirena tipo AG6 y AG8External dummy sounder with Blue lens. AG6 type.

Contacto Magnético COOPER™ 414CTFCOOPER™ 414CTF Magnetic ContactContacto magnético redondo de cobre para empotrar. Cable de 0,3m. Temperatura de trabajo : -25°C - +50°C. Contacto NC.Brass magnetic contact with high mechanical resistance for flush mounting on doors and windows. Reed contact with NC output with near magnet or changeover reed contact. Wire (2 for contact - 3 for changeover contact + 2 for anti-tampering). -25°C to +70°C. IP 65. Anti-tampering wires. 10 pcs./package.

Contacto Magnético ELMDENE™ EN3-QFC-GNELMDENE™ EN3-QFC-GN Magnetic ContactContacto magnético para empotrar con resistencia de 1K. Cable de 6 hilos con resistencia final de línea integrada. Protección IP67. Fondo: 23mm. Fondo del magnético: 13, Borde superior: 36x22.5. Plastic flush contact, plastic, 6 wires, resistors 1k/1k, gap 13mm, cable 1m. This MG contact is available with following EOL resistors too: 4k7/2k2, 8k2/8k2, 4k7/4k7, 6k8/4k7, 5k6/5k6 and 2k2/2k2.

Contacto Magnético CQR™ FC508/WH/MULTI/G3CQR™ FC508/WH/MULTI/G3 Magnetic ContactContacto magnético empotrable. Distancia 6 mm. 4 Terminales. Tamper con micro interruptor. Acabado blanco (marrón bajo pedido). Resistencias seleccionables de final de línea. Clemas de contacto sin necesidad de caja de conexión externa. Puede ser configuardo como doble contacto. Aplicable a puertas de doble hoja. Medidas 20 mm (diámetro) x 32 x 33 mm. Certificado Grado 3 Sistema 5.Flush Quick Fit Door Contact. Screw terminal block, no junction box required. Microswitch tamper. Selectable end of line resistor. Can use own resistors. Available in White or Brown. Can be fitted in double pole. Can be used on double door configuration. Magnetic Immunity.

Contacto Magnético CQR™ FC508/WH/MULTI/G2CQR™ FC508/WH/MULTI/G2 Magnetic ContactContacto magnético empotrable. Distancia 17 mm. 4 Terminales. Tamper con micro interruptor. Acabado blanco (marrón bajo pedido). Resistencias seleccionables de final de línea. Clemas de contacto sin necesidad de caja de conexión externa. Puede ser configuardo como doble contacto. Aplicable a puertas de doble hoja. Medidas 20 mm (diámetro) x 32 x 33 mm. Certificado Grado 2 Sistema 5. Flush Quick Fit Door Contact. Screw terminal block, no junction box required. Microswitch tamper. Selectable end of line resistor. Can use own resistors. Available in White or Brown. Can be fitted in double pole. Can be used on double door configuration.

Contacto Magnético HONEYWELL™ 951WG-WHHONEYWELL™ 951WG-WH Magnetic ContactContacto magnético de empotrar, blanco, 10 mm ø Distancia 30 mm3/8'' Diameter Miniature Press Fit Magnetic Contact. With a 3/4'' long magnet, the 951WG is ideal for casement windows, sliding windows, and other thin frame applications. Standard gap: 1-1/4''– the largest gap of any mini 3/8'' contact. 12'' leads are standard. Switch Type: Form A (SPST) Reed. Contact Rating: 300ma @ 30VDC.

Contacto Magnético HONEYWELL™ MPS9WHONEYWELL™ MPS9W Magnetic ContactContacto magnético de empotrar, blanco, 9,5 mm ø. Distancia 32 mmRecessed-Mounted Contact. Gap (+/- 10%): 1-1/4'' (32 mm). Switch Dimensions: 3/8'' diameter, 3/4'' L (9.5 mm diameter, 19 mm L). Magnet Dimensions: 3/8'' diameter, 3/4'' L (9.5 mm diameter, 19 mm L).

Contacto Magnético HONEYWELL™ EMPS-75WHONEYWELL™ EMPS-75W Magnetic ContactContacto magnético para montaje en empotrado. Normalmente cerrado (puerta cerrada). Potencia nominal: 20 mm. Color blanco. Certificado EN50131-2-6:2009-5 Grado 2 Clase Ambiental II. Diámetro de 16 mm.Magnetic contact, with tamper loop, flush mount, 20 mm. gap, 5 screw terminals, white

Contacto Magnético HONEYWELL™ EMPS70WHONEYWELL™ EMPS70W Magnetic ContactContacto magnético para montaje empotrado. Potencia nominal: 20 mm. Color blanco. Certificado EN50131-2-6:2009-5 Grado 2 Clase Ambiental II.Magnetic contact, with tamper loop, flush mount, 20 mm. gap, 0.3 m. cable, white

Contacto Magnético HONEYWELL™ EMPS10WHONEYWELL™ EMPS10W Magnetic ContactContacto magnético blanco, montaje en superficie, distancia nominal 12 mm. Contacto magnético para montaje en superficie. Normalmente cerrado (puerta cerrada). Potencia nominal: 12 mm. Color blanco. Certificado EN50131-2-6:2009-5 Grado 2 Clase Ambiental II. Diámetro de 8 mm.Magnetic contact, with tamper loop, flush mount, 12 mm. gap, 0.3 m. cable, white.

Contacto Magnético HONEYWELL™ 947-75WHHONEYWELL™ 947-75WH Magnetic ContactContacto Magnético de montaje empotrable para aplicaciones residenciales. Espacio vacío (GAP)(mm): 19. Tipo de salida con el imán puesto: N/C. Tipo de salida sin imán: N/O. Tipo de Montaje: Empotrable en puerta metálica. Diámetro cm: 0.75. Color: Blanco. The Honeywell 947-75 is a 3/4” diameter steel door recessed contact designed to protect steel doors from intrusion. You will need to wire your 947-75 recessed contact back to an open wired zone on your alarm control panel. You will need to splice the wire leads coming out of the backside of the 947-75 recessed contact to the contact loop wire coming from your alarm control panel. Most people prefer recessed contacts to surface mount contacts as they provide a cleaner look. While surface mount contacts distract from the decor of your property, recessed contacts are hidden within your door and window frames and are therefore much less obtrusive. Unfortunately, as recessed contacts need to be drilled into a door or window, they are typically smaller devices. When you install a small magnet inside a steel door, the magnetic field normally gets obstructed and the contact does not work. However, the 947-75 uses a much larger magnet which is able to penetrate the steel door and energize the recessed contact. The steel door recessed contact is ideal for commercial and industrial applications. The Honeywell steel door recessed contact has an internal reed switch with a rating of 100mA at 28VDC. The reed switch is a Form A, SPST, normally closed contact that can be wired to any normally closed zone. When the corresponding magnet is in close proximity to the contact, the contact loop is closed and the alarm control panel is happy. If the steel door opens while the system is armed, the magnet separates from the contact and the loop opens causing an alarm. The magnet spacing gap of the 947-75 recessed contact is 1/2” when installed within a steel door.

Contacto Magnético HONEYWELL™ 956WH-BHONEYWELL™ 956WH-B Magnetic ContactContacto mecánico de bola montaje empotrado. Punto de activación por presión “Roll-on” 360º. No requiere imán. Suministro en paquete de 5 unidades. Color blanco. Normalmente cerrado (puerta cerrada).The Honeywell 956WH-B is a recessed rolling plunger switch with leads. White colour. The recessed rolling plunger switch has a contact rating of 100mA at 28VDC. Plunger switches with terminal screws are typically easier to install, but some installers prefer wire leads over terminal screws. With the 956WH-B, you simply splice your zone wire to the (2) conductor 18” wire leads that come out of the back of the plunger switch. Make sure to use wire crimps or tape to cover any exposed wire after connecting the wires. The 956WH-B requires you to drill a 3/4” diameter hole in your door or window frame so that you can press the plunger switch into place to complete your installation. You can wire the Honeywell 956WH-B recessed rolling plunger switch to an open zone on any alarm control panel. If you are connecting your 956WH-B to a Honeywell alarm control panel, you should program the zone as either a perimeter zone type or an entry/exit delay zone type. The perimeter zone type will trigger an alarm anytime the system is armed and the door or window opens. With an entry/exit delay zone type, the 956WH-B will activate the programmed entry delay time as soon as the roller ball pops out of the plunger switch. If a valid user code is not entered before the entry delay times out, an alarm will be triggered.

Contacto Magnético COOPER™ 462MCOOPER™ 462M Magnetic ContactContacto magnético de aluminio superficie. Apertura 20 mm. Construido en aluminio de estructura robusta, siendo adecuado para aplicaciones en fábricas, tiendas, comercial, etc... Terminales de conexión. Reed con salida NC. Conexión de tipo A. Temperatura. -10 ° C a + 40 ° C. Grado de protección IP 34. Tamper antisabotaje.Aluminum magnetic contact for surface mounting. Thanks to its solid die-cast aluminum structure, it is suitable for applications in factories, shopping malls, etc. Its long operating distance allows the use on frames of any material and with large play. Available with wire and terminal connection (462 model). The wire connected version has a reed section that contains a tight reed with polyurethane resin and an anti-tampering loop to reduce violation risks. The terminal connected version is provided with tear-off protection and a printed circuit board that can house balancing resistors. Arranged to be protected with a 10 mm diameter black PVC coated steel cable sheath (not included).

Contacto Magnético COOPER™ 460SCOOPER™ 460S Magnetic ContactContacto magnético de aluminio superficie. Apertura 21 mm. Construido en aluminio de estructura robusta, siendo adecuado para aplicaciones en fábricas, tiendas, comercial, etc... Aplicable para montaje sobre cualquier tipo de superficie como metal, aluminio, madera, PVC, etc... Reed con salida NC. Conexión de tipo A. Temperatura. -10 ° C a + 40 ° C.Aluminum magnetic contact for surface mounting. Thanks to its solid die-cast aluminum structure, it is suitable for applications in factories, shopping malls, etc. Its long operating distance allows the use on frames of any material and with large play. Available with wire and terminal connection (462 model). The wire connected version has a reed section that contains a tight reed with polyurethane resin and an anti-tampering loop to reduce violation risks. The terminal connected version is provided with tear-off protection and a printed circuit board that can house balancing resistors. Arranged to be protected with a 10 mm diameter black PVC coated steel cable sheath (not included).